⭐ Atomo12345 Posted November 8 Author Report Share Posted November 8 (edited) The best and usefull indicators for this software are "TS Spectrum +" and "Pattern Similarity". With TS Spectrum + you can find the minimums and maximus of the cycles in a relative period. With Pattern Similarity you can find an accurate graphic similarity with a past series of the graphic. Greetings. Atomo. Edited November 8 by Atomo12345 ⭐ RichardGere 1 Quote Link to comment Share on other sites More sharing options...
⭐ laser1000it Posted November 10 Report Share Posted November 10 I can't install this software .....there are several procedures fos searching to 004FBF9C other 004DC009. in both issue I don't see 0053012C address Quote Link to comment Share on other sites More sharing options...
spookie Posted November 10 Report Share Posted November 10 Hi, can you tell us how find f2 breakpoint with microsft calculator? thank you Quote Link to comment Share on other sites More sharing options...
⭐ Atomo12345 Posted November 10 Author Report Share Posted November 10 Use this last procedure and DreamCalc to calculate in base N. https://e.pcloud.link/publink/show?code=XZhEYxZTsbaq2WOiFVy68idrNKPpJOI3LR7 Laser1000it you must find your OptionalHeader.AddressOfEntryPoint and not searching to 004FBF9C other 004DC009 or 0053012C address. General way to find the address where to put the F2 breakpoint.txt Quote Link to comment Share on other sites More sharing options...
spookie Posted November 11 Report Share Posted November 11 Thank you very much Quote Link to comment Share on other sites More sharing options...
pratap Posted November 15 Report Share Posted November 15 hi this is pratap. is there any video to explain the Timing solutions installation, i am struck after instalation, trying to do crack in oldy, but i am unable to do... please help me... Quote Link to comment Share on other sites More sharing options...
rtt518 Posted November 15 Report Share Posted November 15 yes please use any video to explain it Quote Link to comment Share on other sites More sharing options...
⭐ RichardGere Posted November 15 Report Share Posted November 15 I heard from someone that this could be the serial is moving around in memory each time the program is run. This is to prevent from fishing out the serial. I am not sure if this is the case. Perhaps, for those who want to use the program may consider using the patch as provided by Kesk in his timing solution & Nifty 2 update thread. Quote Link to comment Share on other sites More sharing options...
⭐ kesk Posted Saturday at 04:07 AM Report Share Posted Saturday at 04:07 AM If you are technical savvy, the program is using Address space layout randomization method. So the address you see one time may not be the same again when you restart the program/computer. Even with the debugger its the same. So the address to catch the serial wont work unless one knows how to really debug or calculate the shifts in address. Thats the reason I left the original patcher alone! In the not so old setups, there used to be TS.exe and TSA.exe where there is no ASLR but nowadays only TS.exe which runs either as TSA or TI mode and it uses the ASLR tech. ⭐ RichardGere 1 Quote Link to comment Share on other sites More sharing options...
⭐ Atomo12345 Posted Saturday at 11:15 AM Author Report Share Posted Saturday at 11:15 AM (edited) Sorry, but my general method don't work nevermore. However if you have your old key this works also for the new updates of the software. Thank you kesk for your updates of the program. Have a good week end. Atomo. Edited Saturday at 11:17 AM by Atomo12345 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.